12V / 24V Solar Panel Battery Regulator Charge Controller supply by UNICELL in Singapore
UNICELL a Leading solar product supplier in Singapore Malaysia Indonesia Philippines Brunei and Thailand since 1986 , we carry more the 66,000 model
Order code : SLP-12030A-PMW ( 12V 24V 30A solar controller )
12V or 24V 30A Solar Panel Battery Regulator Charge Controller
Product description: 12V/24V Auto Solar charge controller, have battery capacity indicator. Also carry with overload, short circuit, lighting, under voltage, over voltage, over charged, anti-access protection.
Fuction:
1. Over-load protection
2. Short circuit protection
3. Lightning protection
4. Under-voltage protection
5. Over-charging protection
CONNECTION (AS INDICATED IN DIAGRAM):
Open the top cover of controller and connect the wire with terminals follow the diagram on the top cover of it.
1. Connect the “+”, “-” Poles of the battery to the corresponding ports of controller (the third and the fourth one from left). * The subsequent operation can be processed if only if load indicator (mark: load) flickers once and starts lighting after 15 seconds. Otherwise, the subsequent operation will damage the controller.
2. Connect the “+”, “-” poles of the solar panel to the corresponding ports of controller (the first and the second one from left). * If a connection error can damage your controller.
3. Connect the “+”, “-” poles of the load to the corresponding ports of controller (the fifth and the sixth one from left).
Ⅲ. INDICATOR LED
1. Solar LED is used to indicate the charging status of battery. Lighting is in-charging mode, flickering is floating charge mode. LED turn off means charging stopped.
2. There is output and load can work if the Load LED is lighting. There isn’t output and the load cannot work if Load LED off.
Notice:
1. Please make sure the rated voltage of solar panels, batteries the loads are same. All of them should be 12V or 24V.
2. The rated current of solar panels and load must be less than the rated current of controller.
Features:
1. This product has protection from overcharge and over discharge.
2. It employs PMW charging main circuit which is in tandem type and makes the voltage loss reduce to almost 50% compared to that resulting from using charging circuit of diode. The charging efficiency of the former is 3%-6% higher than non-PMW charging
circuit, thus extending the time length of electricity use. It has the automatic control mode consisting of booster tension of over
discharge recovery, direct charging and floating charging, which extends the system service life.
3. The intuitive LED luminous tube indicates the state of the battery, enabling users to be aware of it.
Specification:
Rated charging current : 30A
Rated discharging current : 30A
Voltage : 12V/24V Auto switch
No load losses : <5mA;
Charging circuit voltage drop : Less than or equal to 0.20V
Discharge circuit voltage drop : Less than or equal to 0.15V
Over voltage protection : 17V;x2/24V;
boost charge voltage : 14.6V;x2/24V (time of duration: 10 minutes)
Direct charge voltage : 14.4V;x2/24V (time of duration: 10 minutes)
Float charge voltage : 13.6V;x2/24V
Charge recover voltage : 13.2V;x2/24V
Over discharge recover voltage : 12.5V;x2/24V
Lower voltage indication : 12.0V;x2/24V
Over discharge voltage : 11.1V x2/24V
Temperature compensation : -4.0mV//2V(boost voltage, direct charge, float charge and charge return voltage compensation)
Control method : PWM Smart Charging
Working temperature : From -35°c to +65°c
Fit or replace part no. : (Cross refer or compatible chart )
Fit or replace product model: (Cross refer or compatible chart )
Unicell International is not affiliated in any way with any of the manufacturers listed in this catalogue and the batteries sold in this catalogue have not been sponsored or approved by any of such manufacturers. Any trademarks or model numbers listed in this catalogue are identified for compatibility or cross-reference purposes only |
